You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
129 lines
8.0 KiB
129 lines
8.0 KiB
#include "Arduino.h"
|
|
|
|
//######################### INFOS ####################################
|
|
/* This is a develboard-specific config-file for ESPuino complete with port-expander PCA9555.
|
|
PCB: tba
|
|
Infos: tba
|
|
Caveats: None
|
|
Status: untested / unfinished
|
|
*/
|
|
|
|
//################## GPIO-configuration ##############################
|
|
// Please note: GPIOs 34, 35, 36, 39 are input-only and don't have pullup-resistors.
|
|
// So if connecting a button to these, make sure to add a 10k-pullup-resistor for each button.
|
|
// Further infos: https://randomnerdtutorials.com/esp32-pinout-reference-gpios/
|
|
#ifdef SD_MMC_1BIT_MODE
|
|
// uSD-card-reader (via SD-MMC 1Bit)
|
|
//
|
|
// SD_MMC uses fixed pins
|
|
// MOSI 15
|
|
// SCK 14
|
|
// MISO 2
|
|
#else
|
|
// uSD-card-reader (via SPI)
|
|
#define SPISD_CS 15 // GPIO for chip select (SD)
|
|
#ifndef SINGLE_SPI_ENABLE
|
|
#define SPISD_MOSI 13 // GPIO for master out slave in (SD) => not necessary for single-SPI
|
|
#define SPISD_MISO 16 // GPIO for master in slave ou (SD) => not necessary for single-SPI
|
|
#define SPISD_SCK 14 // GPIO for clock-signal (SD) => not necessary for single-SPI
|
|
#endif
|
|
#endif
|
|
|
|
// RFID (via SPI)
|
|
#define RST_PIN 22 // Not necessary but has to be set anyway; so let's use a dummy-number
|
|
#define RFID_CS 21 // GPIO for chip select (RFID)
|
|
#define RFID_MOSI 23 // GPIO for master out slave in (RFID)
|
|
#define RFID_MISO 19 // GPIO for master in slave out (RFID)
|
|
#define RFID_SCK 18 // GPIO for clock-signal (RFID)
|
|
|
|
#ifdef RFID_READER_TYPE_PN5180
|
|
#define RFID_BUSY 16 // PN5180 BUSY PIN
|
|
#define RFID_RST 22 // PN5180 RESET PIN
|
|
#define RFID_IRQ 39 // PN5180 IRQ PIN (only needed for low power card detection)
|
|
#endif
|
|
// I2S (DAC)
|
|
#define I2S_DOUT 25 // Digital out (I2S)
|
|
#define I2S_BCLK 27 // BCLK (I2S)
|
|
#define I2S_LRC 26 // LRC (I2S)
|
|
|
|
// Rotary encoder
|
|
#ifdef USEROTARY_ENABLE
|
|
#define ROTARYENCODER_CLK 35 // If you want to reverse encoder's direction, just switch GPIOs of CLK with DT (in software or hardware)
|
|
#define ROTARYENCODER_DT 34 // Info: Lolin D32 / Lolin D32 pro 35 are using 35 for battery-voltage-monitoring!
|
|
#define ROTARYENCODER_BUTTON 105 // (set to 99 to disable; 0->39 for GPIO; 100->115 for port-expander)
|
|
#endif
|
|
|
|
// Amp enable (optional)
|
|
#define GPIO_PA_EN 112 // To enable amp for loudspeaker (GPIO or port-channel)
|
|
#define GPIO_HP_EN 113 // To enable amp for headphones (GPIO or port-channel)
|
|
|
|
// Control-buttons (set to 99 to DISABLE; 0->39 for GPIO; 100->115 for port-expander)
|
|
#define NEXT_BUTTON 102 // Button 0: GPIO to detect next
|
|
#define PREVIOUS_BUTTON 103 // Button 1: GPIO to detect previous (Important: as of 19.11.2020 changed from 33 to 2; make sure to change in SD-MMC-mode)
|
|
#define PAUSEPLAY_BUTTON 100 // Button 2: GPIO to detect pause/play
|
|
#define BUTTON_4 101 // Button 4: unnamed optional button
|
|
#define BUTTON_5 104 // Button 5: unnamed optional button
|
|
|
|
// Channels of port-expander can be read cyclic or interrupt-driven. It's strongly recommended to use the interrupt-way!
|
|
// Infos: https://forum.espuino.de/t/einsatz-des-port-expanders-pca9555/306
|
|
#ifdef PORT_EXPANDER_ENABLE
|
|
#define PE_INTERRUPT_PIN 4 // GPIO that is used to receive interrupts from port-expander
|
|
#endif
|
|
|
|
// I2C-configuration (necessary for RC522 [only via i2c - not spi!] or port-expander)
|
|
#if defined(RFID_READER_TYPE_MFRC522_I2C) || defined(PORT_EXPANDER_ENABLE)
|
|
#define ext_IIC_CLK 33 // i2c-SCL (clock)
|
|
#define ext_IIC_DATA 5 // i2c-SDA (data)
|
|
#endif
|
|
|
|
// Wake-up button => this also is the interrupt-pin if port-expander is enabled!
|
|
// Please note: only RTC-GPIOs (0, 4, 12, 13, 14, 15, 25, 26, 27, 32, 33, 34, 35, 36, 39, 99) can be used! Set to 99 to DISABLE.
|
|
// Please note #2: this button can be used as interrupt-pin for port-expander. If so, all pins connected to port-expander can wake up ESPuino.
|
|
#define WAKEUP_BUTTON ROTARYENCODER_BUTTON // Defines the button that is used to wake up ESPuino from deepsleep.
|
|
|
|
// (optional) Power-control
|
|
#define POWER 13 // GPIO used to drive transistor-circuit, that switches off peripheral devices while ESP32-deepsleep
|
|
|
|
// (optional) Neopixel
|
|
#define LED_PIN 12 // GPIO for Neopixel-signaling
|
|
|
|
// (optinal) Headphone-detection
|
|
#ifdef HEADPHONE_ADJUST_ENABLE
|
|
#define DETECT_HP_ON_HIGH // Per default headphones are supposed to be connected if HT_DETECT is LOW. DETECT_HP_ON_HIGH will change this behaviour to HIGH.
|
|
#define HP_DETECT 107 // GPIO that detects, if there's a plug in the headphone jack or not
|
|
#endif
|
|
|
|
// (optional) Monitoring of battery-voltage via ADC
|
|
#ifdef MEASURE_BATTERY_VOLTAGE
|
|
#define VOLTAGE_READ_PIN 33 // GPIO used to monitor battery-voltage. Change to 35 if you're using Lolin D32 or Lolin D32 pro as it's hard-wired there!
|
|
constexpr float referenceVoltage = 3.35; // Voltage between 3.3V and GND-pin at the develboard in battery-mode (disconnect USB!)
|
|
constexpr float offsetVoltage = 0.1; // If voltage measured by ESP isn't 100% accurate, you can add an correction-value here
|
|
#endif
|
|
|
|
// (optional) For measuring battery-voltage a voltage-divider is necessary. Their values need to be configured here.
|
|
#ifdef MEASURE_BATTERY_VOLTAGE
|
|
constexpr uint8_t rdiv1 = 100; // Rdiv1 of voltage-divider (kOhms) (measure exact value with multimeter!)
|
|
constexpr uint16_t rdiv2 = 33; // Rdiv2 of voltage-divider (kOhms) (measure exact value with multimeter!) => used to measure voltage via ADC!
|
|
#endif
|
|
|
|
// (Optional) remote control via infrared
|
|
#ifdef IR_CONTROL_ENABLE
|
|
#define IRLED_PIN 22 // GPIO where IR-receiver is connected (only tested with VS1838B)
|
|
#define IR_DEBOUNCE 200 // Interval in ms to wait at least for next signal (not used for actions volume up/down)
|
|
|
|
// Actions available. Use your own remote control and have a look at the console for "Command=0x??". E.g. "Protocol=NEC Address=0x17F Command=0x68 Repeat gap=39750us"
|
|
// Make sure to define a hex-code not more than once as this will lead to a compile-error
|
|
// https://forum.espuino.de/t/neues-feature-fernsteuerung-per-infrarot-fernbedienung/265
|
|
#define RC_PLAY 0x68 // command for play
|
|
#define RC_PAUSE 0x67 // command for pause
|
|
#define RC_NEXT 0x6b // command for next track of playlist
|
|
#define RC_PREVIOUS 0x6a // command for previous track of playlist
|
|
#define RC_FIRST 0x6c // command for first track of playlist
|
|
#define RC_LAST 0x6d // command for last track of playlist
|
|
#define RC_VOL_UP 0x1a // Command for volume up (one step)
|
|
#define RC_VOL_DOWN 0x1b // Command for volume down (one step)
|
|
#define RC_MUTE 0x1c // Command to mute ESPuino
|
|
#define RC_SHUTDOWN 0x2a // Command for deepsleep
|
|
#define RC_BLUETOOTH 0x72 // Command to enable/disable bluetooth
|
|
#define RC_FTP 0x65 // Command to enable FTP-server
|
|
#endif
|