fixing logical merge errors

src/main.cpp

@@ -3441,7 +3441,7 @@ void onWebsocketEvent(AsyncWebSocket *server, AsyncWebSocketClient *client, AwsE
         client->ping();
     } else if (type == WS_EVT_DISCONNECT) {
         //client disconnected
-        Serial.printf("ws[%s][%u] disconnect: %u\n", server->url(), uint(client->id()));
+        Serial.printf("ws[%s][%u] disconnect: %u\n", server->url(), uint8_t(client->id()));
     } else if (type == WS_EVT_ERROR) {
         //error was received from the other end
         Serial.printf("ws[%s][%u] error(%u): %s\n", server->url(), client->id(), *((uint16_t*)arg), (char*)data);
@@ -3743,8 +3743,8 @@ void setup() {
     Serial.printf("Built-In Amplifier enabled\n");
 #endif
 
-    #if not defined SINGLE_SPI_ENABLE
-       #ifdef SD_MMC_1BIT_MODE
+    #ifndef SINGLE_SPI_ENABLE
+      #ifdef SD_MMC_1BIT_MODE
         pinMode(2, INPUT_PULLUP);
       #else
         // Init uSD-SPI
@@ -3759,15 +3759,8 @@ void setup() {
             SPI.begin();
             SPI.setFrequency(1000000);
         #endif
-        #ifdef RFID_READER_TYPE_MFRC522_I2C
-            i2cBusTwo.begin(ext_IIC_DATA, ext_IIC_CLK, 40000);
-        #endif
     #endif
 
-    mfrc522.PCD_Init();
-    delay(50);
-    loggerNl((char *) FPSTR(rfidScannerReady), LOGLEVEL_DEBUG);
-
     #ifndef SINGLE_SPI_ENABLE
         #ifdef SD_MMC_1BIT_MODE
             while (!SD_MMC.begin("/sdcard", true)) {
@@ -3788,6 +3781,14 @@ void setup() {
 
         }
 
+    #ifdef RFID_READER_TYPE_MFRC522_I2C
+        i2cBusTwo.begin(ext_IIC_DATA, ext_IIC_CLK, 40000);
+    #endif
+
+    mfrc522.PCD_Init();
+    delay(50);
+    loggerNl((char *) FPSTR(rfidScannerReady), LOGLEVEL_DEBUG);
+
    // welcome message
    Serial.println(F(""));
    Serial.println(F("_____         _____ _____ _____ _____     "));

src/settings-espa1s.h

@@ -1,25 +1,14 @@
 #include "Arduino.h"
 
 //################## GPIO-configuration ##############################
-#ifdef SD_MMC_1BIT_MODE
-    #define SPISD_CS                        15          // GPIO for chip select (SD)
-    // uSD-card-reader (via SD-MMC 1Bit)
-    //
-    // SD_MMC uses fixed pins
-    //  MOSI    15
-    //  SCKK    14
-    //  MISO    2   // hardware pullup may required
-#else
-    // uSD-card-reader (via SPI)
-    #define SPISD_CS                        15          // GPIO for chip select (SD)
-    #ifndef SINGLE_SPI_ENABLE
-        #define SPISD_MOSI                  13          // GPIO for master out slave in (SD) => not necessary for single-SPI
-        #define SPISD_MISO                  16          // GPIO for master in slave ou (SD) => not necessary for single-SPI
-        #define SPISD_SCK                   14          // GPIO for clock-signal (SD) => not necessary for single-SPI
-    #endif
+// uSD-card-reader (via SPI)
+#define SPISD_CS                        13          // GPIO for chip select (SD)
+#ifndef SINGLE_SPI_ENABLE
+    #define SPISD_MOSI                  15          // GPIO for master out slave in (SD) => not necessary for single-SPI
+    #define SPISD_MISO                   2          // GPIO for master in slave ou (SD) => not necessary for single-SPI
+    #define SPISD_SCK                   14          // GPIO for clock-signal (SD) => not necessary for single-SPI
 #endif
 
-
 #define MFRC522_RST_PIN                 12          // needed for i2c-comm  MTDI on JTAG
 #define MFRC522_ADDR                    0x28        // default Address of MFRC522
 #define ext_IIC_CLK                     23          // 14-pin-header

src/settings.h

@@ -15,8 +15,8 @@
 //#define BLUETOOTH_ENABLE          // Doesn't work currently (so don't enable) as there's not enough DRAM available
 
 //################## select SD card mode #############################
-#define SD_MMC_1BIT_MODE            // run SD card in SD-MMC 1Bit mode
-#define SINGLE_SPI_ENABLE         // If only one SPI-instance should be used instead of two (not yet working!) (Works on ESP32-A1S with RFID via I2C)
+//#define SD_MMC_1BIT_MODE            // run SD card in SD-MMC 1Bit mode
+//#define SINGLE_SPI_ENABLE         // If only one SPI-instance should be used instead of two (not yet working!) (Works on ESP32-A1S with RFID via I2C)
 
 //################## select RFID reader ##############################
 //#define RFID_READER_TYPE_MFRC522_SPI        // use MFRC522 via SPI