Sleeptimer-bugfix

README.md

@@ -132,7 +132,7 @@ Keep in mind the RFID-lib I used is intended for default-SPI-pins only (SCK, MIS
 * If you want to monitor the battery-voltage, make sure to enable `MEASURE_BATTERY_VOLTAGE`. Use a voltage-divider as voltage of a LiPo is way too high for ESP32 (only 3.3V supported!). For my tests I connected VBat with a serial connection of 130k + 390k resistors (VBat--130k--X--390k--GND). X is the measure-point where to connect the GPIO to. Please note: via GUI upper and lower voltage for visualisation of battery-voltage (Neopixel) is available. Additional GUI-configurable values are interval (in minutes) for checking battery voltage and the cut off-voltage below whose a warning is shown via Neopixel.
 * If you're using a headphone-pcb with a [headphone jack](https://www.conrad.de/de/p/cliff-fcr1295-klinken-steckverbinder-3-5-mm-buchse-einbau-horizontal-polzahl-3-stereo-schwarz-1-st-705830.html) that has a pin to indicate if there's a plug, you can use this signal along with the feature `HEADPHONE_ADJUST_ENABLE` to limit the maximum headphone-voltage automatically. As per default you have to invert this signal and connect it to GPIO22.
 * Enabling `SHUTDOWN_IF_SD_BOOT_FAILS` is really recommended if you run your Tonuino in battery-mode without having a restart-button exposed to the outside of the Tonuino's enclosure. Because otherwise there's no way to restart your Tonuino and the error-state will remain until battery is empty (or you open the enclosure, hehe).
-* Enabling `PLAY_LAST_RFID_AFTER_REBOOT` will tell Tonuino to remember the last RFID-tag played after reboot. So rebooting Tonuino will end up in autoplay.
+* Enabling `PLAY_LAST_RFID_AFTER_REBOOT` will tell Tonuino to remember the last RFID-tag played after next reboot. So rebooting Tonuino will end up in autoplay.
 * compile and upload the sketch
 
 ## Starting Tonuino-ESP32 first time

src/main.cpp

@@ -2343,8 +2343,8 @@ void doRfidCardModifications(const uint32_t mod) {
             }
             break;
 
-        case SLEEP_TIMER_MOD_15:    // Puts/undo uC to sleep after 15 minutes
-            if (sleepTimer == 15) {
+        case SLEEP_TIMER_MOD_15:    // Enables/disables sleep after 15 minutes
+            if (sleepTimerStartTimestamp && sleepTimer == 15) {
                 sleepTimerStartTimestamp = 0;
                 #ifdef NEOPIXEL_ENABLE
                     ledBrightness = initialLedBrightness;
@@ -2376,8 +2376,8 @@ void doRfidCardModifications(const uint32_t mod) {
             #endif
             break;
 
-        case SLEEP_TIMER_MOD_30:    // Puts/undo uC to sleep after 30 minutes
-            if (sleepTimer == 30) {
+        case SLEEP_TIMER_MOD_30:    // Enables/disables sleep after 30 minutes
+            if (sleepTimerStartTimestamp && sleepTimer == 30) {
                 sleepTimerStartTimestamp = 0;
                 #ifdef NEOPIXEL_ENABLE
                     ledBrightness = initialLedBrightness;
@@ -2409,8 +2409,8 @@ void doRfidCardModifications(const uint32_t mod) {
             #endif
             break;
 
-        case SLEEP_TIMER_MOD_60:    // Puts/undo uC to sleep after 60 minutes
-            if (sleepTimer == 60) {
+        case SLEEP_TIMER_MOD_60:    // Enables/disables sleep after 60 minutes
+            if (sleepTimerStartTimestamp && sleepTimer == 60) {
                 sleepTimerStartTimestamp = 0;
                 #ifdef NEOPIXEL_ENABLE
                     ledBrightness = initialLedBrightness;
@@ -2442,8 +2442,8 @@ void doRfidCardModifications(const uint32_t mod) {
             #endif
             break;
 
-        case SLEEP_TIMER_MOD_120:    // Puts/undo uC to sleep after 2 hrs
-            if (sleepTimer == 120) {
+        case SLEEP_TIMER_MOD_120:    // Enables/disables sleep after 2 hrs
+            if (sleepTimerStartTimestamp && sleepTimer == 120) {
                 sleepTimerStartTimestamp = 0;
                 #ifdef NEOPIXEL_ENABLE
                     ledBrightness = initialLedBrightness;